SL
Shuang Liu
Author with expertise in Photocatalytic Materials for Solar Energy Conversion
Achievements
This user has not unlocked any achievements yet.
Key Stats
Upvotes received:
0
Publications:
6
(0% Open Access)
Cited by:
1
h-index:
15
/
i10-index:
22
Reputation
Biology
< 1%
Chemistry
< 1%
Economics
< 1%
Show more
How is this calculated?
Publications
0

Research on TiN inclusion modification in 20CrMnTi gear steel by rare earth Ce during Si-Ca-Ba-Ce composite deoxidation

Shuang Liu et al.Aug 9, 2024
The size and distribution of TiN inclusions in 20CrMnTi gear steel directly affect its service performance. A reasonable method for controlling the size of TiN inclusions is a prerequisite for obtaining high-quality 20CrMnTi gear steel. This study focuses on the modification behaviour of TiN inclusions in 20CrMnTi gear steel under the conditions of Si-Ca-Ba single deoxidation and Si-Ca-Ba-Ce composite deoxidation, and their effects on the fatigue performances of the steels. The results show that after Si-Ca-Ba-Ce composite deoxidation, in addition to TiN inclusions, TiN containing composite inclusions such as Al 2 O 3 -TiN and CaAl 12 O 19 -TiN are also generated in the steel. When the ratio of Si-Ca-Ba to Ce in the Si-Ca-Ba-Ce composite deoxidiser is 5:1, the effective modification rate of TiN reaches 48.6%, which is better than 44.8% at 7:1 and 45% at 2.4:1, and the average size of the inclusions in the steel is 2.5 μm, which is better than 2.8 at and 3 μm at 2.4:1. At this point, the effect of the TiN inclusion modification in the steel is good, and the fatigue performance of the 20CrMnTi gear steel has been improved.
0

A Laser Interference-based Flaw Detection Device for Hydraulic Turbine Units

Fulin Zhou et al.Mar 28, 2024
Hydroelectric turbine generator sets play a key role in power production as important energy devices. However, the complexity of its internal structure makes it susceptible to the threat of defects such as cracks, which may pose a serious risk to the safety and reliability of the equipment. Although traditional ultrasonic flaw detection methods are widely used, their application is limited when faced with problems such as high cost, low efficiency, and unclear display of defects. Therefore, this study aims to solve these problems and improve the efficiency and accuracy of defect detection through the development of a laser interference-based flaw detection device for hydro generator sets. The core idea of the device is to detect internal and external defects of the hydraulic turbine unit by analyzing the position and shape of the interference fringes using the laser interference principle. We describe in detail the system components of the device, including the laser scanning system, the flaw detection system and the data acquisition and processing system, as well as the working principle. Through experimental verification, it is proved that the device has the advantages of high precision and high efficiency, and provides a new effective tool for the operation and maintenance of hydropower plants.
0

Ultrasonic measurement of axial preload in anchor rods

Zhongrui Sun et al.Jan 1, 2025
This paper reports on ultrasonic measurement of the axial preload of anchor rods loaded by a pulling machine. The axial preload of ultrasonic measurement was as high as 90 kN, limited by manual operation and the anchor protection structure. Ultrasonic response characterisation, high accuracy and effective ultrasonic measurement of axial preload in anchor rods are reported here and are fully demonstrated. By bonding lead zirconate titanate (PZT) piezoelectric ceramic sensors and self-designed ultrasonic probes on the anchor rods, A-scan ultrasonic signals were successfully measured and originated from the bottom of the hollow anchor rod. The temporal A-scan signal featured a pure and broad frequency spectrum that peaked at around 16 MHz, but no original frequency signal component of the sensors was found. This phenomenon is attributed to the reflective characteristics of the thread-like structure of the hollow anchor rod, potentially inducing a non-linear ultrasound effect, independent of the test instrumentation and coupling agent. When the loading tension of the calibrated pulling machine is lower than 30 kN, the axial preload of the anchor rods obtained from the ultrasonic measurement has an error as high as ±16%. By comparison, the error is less than ±5% for the tension increasing from 60 kN to 90 kN. The experimental results indicate that the proposed ultrasonic measurement method is a simple, accurate and effective way to obtain the axial preload of anchor rods.